|
|
 |
HIGH PERFORMANCE |
|
| GLASS CUTTING FLUIDS |
ACECUT 5250 ACECUT 5250 is specifically developed for insulating glass and window manufacturers who process soft coated Low-E glass, applicable to all state of the art vacuum deposited and sputter coated coatings. ACECUT 5250 is a totally evaporating cutting fluid, producing excellent scoring and break-out qualities. ACECUT 5250 if properly applied, leaves NO residual cutting fluid on the glass edge,thus your washer water is not contaminated and most importantly, adhesion of sealants is not impaired. ACECUT 5250 should be used ideally where cycle times between cutting and break-out are short. As a guide line, this fluid is ideal for glass thickness range from 3/32" - 3/16" with stock sheets up to 48 square feet. Theoretical evaporation time with glass surface temperature @ 30°C (86°F) is approximately 20-25 minutes. ACECUT 5503 ACECUT 5503 is in application characteristics identical to Acecut 5250, however it evaporates somewhat slower. As a guide line this fluid is ideal for the residential I-G/Window manufacturers who processes stock sheets 96" x 130/108" x 144" and a glass thickness range of 3/32" to 1/4". Theoretical evaporation time with glass surface temperature of 30°C (86°F) is approximately 40 minutes ACECUT 5503 is specifically developed
for insulating glass and window manufacturers who process soft coated LOW-E glass. ACECUT 5503 if properly applied
leaves no residual cutting fluid on the glass edges thus your washer
water is not contaminated, and most importantly, adhesion of
sealants to glass is not impaired. ACECUT 5503 can also be used to cut clear float and hard coated glass. ACECUT 6613 ACECUT 6613 is, in its application characteristically identical to ACECUT 5503, yet it evaporates somewhat slower than ACECUT 5503 Acecut 6613 is the newest development in high quality evaporating glass cutting fluids from our German manufacturing supplier. Acecut 6613 is ideal for the residential I-G/window manufacturers. Acecut 6613 is safe to use with ALL soft coated LOW-E glasstypes. Theoretical evaporation time with a glass surface temperature of 30° C (86° F) is approximately 60 minutes. ACECUT 5929 ACECUT 5929 is, in its application characteristics identical to ACECUT 5250 and 5503. Acecut 5929 should be used where cycle times between cutting and break-out are fairly long, in other words commercial I-G manufacturers who process jumbo size sheets (130" x 204") with a thickness range of 1/8" to 1/2". Theoretical evaporation time with glass surface temperature 30° C (86°F) is approximately 97 minutes. ACECUT 5929 renders the same characteristics as ACECUT 5503, however it evaporates considerably slower. For example, ACECUT 5929 is widely used by glass processors who cut large (jumbo size) stock sheets into many small sizes, where time cycles between cutting and break-out are longer than with smaller stock sizes. ACECUT 6336 ACECUT 6336 is in its application characteristics, identical to ACECUT 5250, 5503, and 5929. ACECUT 6336 is an extremely slow, yet fully evaporating cutting fluid. This fluid may be applied for thick, soft coated jumbo sheets from which large numbers of small sizes are processed, or for any special application where the cutting fluid has to remain active for a long time. Theoretical evaporation time with glass surface temperature @ 30°C (86°F) is approximately 480 minutes.
MINERAL OIL BASED GLASS CUTTING FLUIDS ACECUT 6000 ACECUT 6000 is a high performance glass cutting fluid for superior quality break-out demands. Typically Acecut 6000 is used for automotive glass where tight radii and tolerances are required as well as for very thick glass for the furniture industry. Flat glass which requires edgework after cutting should have a clean and straight break in order to minimize wear on diamond wheels. ACECUT
6000 has a unique
characteristic in that it penetrates the score (cut) fast and deep
and prevents the score (cut) from healing again, resulting in
consistent good clean and straight breaks (Note: Part of attaining
good break-out results also require a good quality cutting wheel,
correct wheel angle and pressure. ACECUT 6000 should not be used on soft coated glass. ACECUT 4153 ACECUT 4153 is a water soluble mineral oil based cutting fluid. It may be used for automotive glass cutting with glass thickness not exceeding 1/4" (6mm). ACECUT 4153 is a lower viscosity fluid than Acecut 6000, thus more favorable for older cutting machines in regard to fluidity. ACECUT 4153 is not recommended for soft coated glass. ACECUT NT ACECUT
NT glass cutting fluid
is used for general straight line cutting. |
